• +852 62687107
  • info@powerstability.com
  • HongKong

APS Series-Short Section On Monitoring Of Drilling Parameters

Short section on monitoring of drilling parameters
Short section on monitoring of drilling parameters
Short section on monitoring of drilling parameters
Short Section On Monitoring Of Drilling Parameters
Size: 4.75", 6.75", 8.00"
Temperature: 150°C, 175°C
Provide the true pressure value of the near drill bit
Provide the true torque value of the near drill bit
Provide the bending moment of the near drill bit
Provide the bending angle of the near drill bit
Provide the annular pressure value of the near drill bit
Provide the water eye pressure in the tooling of the near drill bit
Provide the temperature value at the near drill bit
Ingredient
3 strain transducer compartments
3 circuit board compartments
Data communication port
Upper and lower salvage section
Upper and lower centre piercing retainer assembly
Process characteristics
Selection of high-precision strain and temperature sensors
Precise sensor position mounting
Clean Room sensor assembly
Factory calibration
137 sets of pressure, temperature and load cut-off data calibration
Strain sensors - drilling pressure, torque, bending moment, bending angle
120° uniform
Strain sensors are subjected to tensile, torsional and bending forces.
The sensor is subjected to a force that produces a corresponding strain.
Strain causes the sensor to deform, increasing or decreasing its resistance.
Each chamber contains axial and torsional Wheatstone bridges.
The change in resistance in the Wheatstone bridge will be linearly related to the force applied.
Sensor homogenisation and multiple Wheatstone bridges improve measurement accuracy
Shape design provides predictable and repeatable stress-strain behaviour
Calibration process
Tensile and compressive load calibration
NIST'' compliant loading device
Bending moment load calibration
Torque cut load calibration
Zero lifting
WOB lifting zero calibration
Short Section On Monitoring Of Drilling Parameters
Size: 4.75"
Drilling pressure measurement: ±30 Klbs
Borehole: 5.25" - 6.50"
Maximum size: 5.245"
Torque measurement: ±14 Kftibs
Temperature: 150°C, 175°C
Salvage size: 4.90"
Bending moment training: ±11 Kftibs
Pressure: 20KPsi
Inside Diameter: 1.50"
Accuracy: ±5% absolute
Maximum Survival Pressure: 26.5KPsi
Overall Length: 84.0"
Repeatability: ±1% absolute
( Rotating ) Bend Radius: ≤12°/30m
Buckle Type: 3.5 "IF BOX x 3.5 "IF BOX
Resolution: 1%
( Sliding ) Bend Radius: ≤24°/30m
Memory: 32MB
Annular pressure: 20 KPsi
Material: P550
Water eye pressure: 20 KPsi
Mode: Stored, MWD real-time transmission
Accuracy value: 0.1% FSR
Short Section On Monitoring Of Drilling Parameters
Size: 6.75"
Drilling pressure measurement: ±60 Klbs
Borehole: 8.5" - 9.875"
Maximum size: 7.25"
Torque measurement: ±30 Kftibs
Temperature: 150°C, 175°C
Salvage size: 6.91"
Bending moment training: ±30 Kftibs
Pressure: 20KPsi
Inside Diameter: 2.813"
Accuracy: ±5% absolute
Maximum Survival Pressure: 26.5KPsi
Overall Length: 84.0"
Repeatability: ±1% absolute
( Rotating ) Bend Radius: ≤10°/30m
Buckle Type: 4.5 "IF BOX x 4.5 "IF BOX
Resolution: 1%
( Sliding ) Bend Radius: ≤22°/30m
Memory: 32MB
Annular pressure: 20 KPsi
Material: P550
Water eye pressure: 20 KPsi
Mode: Stored, MWD real-time transmission
Accuracy value: 0.1% FSR
Short Section On Monitoring Of Drilling Parameters
Size: 8.00"
Drilling pressure measurement: ±100 Klbs
Borehole: 10.625" - 17.5"
Maximum size: 8.22"
Torque measurement: ±50 Kftibs
Temperature: 150°C, 175°C
Salvage size: 8.00"
Bending moment training: ±45 Kftibs
Pressure: 20KPsi
Inside Diameter: 3.25"
Accuracy: ±5% absolute
Maximum Survival Pressure: 26.5KPsi
Overall Length: 92.5"
Repeatability: ±1% absolute
( Rotating ) Bend Radius: ≤8°/30m
Buckle Type: 6 5/8 "IF BOX x 6 5/8 "IF BOX
Resolution: 1%
( Sliding ) Bend Radius: ≤20°/30m
Memory: 32MB
Annular pressure: 20 KPsi
Material: P550
Water eye pressure: 20 KPsi
Mode: Stored, MWD real-time transmission
Accuracy value: 0.1% FSR

Other APS Series

Ultra Small Borehole Tool

Ultra Small Borehole Tool

Directional Measuring Unit

Directional Measuring Unit

Downhole Power Supply Mode

Downhole Power Supply Mode

Universal Integrator

Universal Integrator

Electromagnetic wave resistivity with drilling

Electromagnetic wave resistivity with drilling

Density & Porosity Measurement Tools

Density & Porosity Measurement Tools

Short Section On Pressure Measurement With Drilling Function

Short Section On Pressure Measurement With Drilling Function

Azimuthal Gamma

Azimuthal Gamma

Natural Gamma (LWD)

Natural Gamma (LWD)

Rotary Guide Drilling Tools

Rotary Guide Drilling Tools-A

Rotary Guide Drilling Tools

Rotary Guide Drilling Tools-B

Short Section On Vibration Monitoring

Short Section On Vibration Monitoring

Intelligent Damping Instruments

Intelligent Damping Instruments

QUICK INQUIRY

Please enable JavaScript in your browser to complete this form.
Name